Silex technology MNS-300EM Скачать руководство пользователя страница 77

Страница: 77 / 134

7. Server Commands

Shows the network statistics for the server.

SH SERVEr CO

Sample output:
Local > SH SERVEr CO

Seconds Since Zeroed:

28 Frames Sent, 1 Collision:

N/A

Bytes Received:

0 Frames Sent, 2+ Collision:

N/A

Bytes Sent:

0 Send Failures:

Frames Received:

0 Send Failure Reasons:

N/A

Frames Sent:

0 Receive Failures:

Multicast Bytes Rcv'd:

N/A Receive Failure Reasons:

N/A

Multicast Bytes Sent:

N/A Unrecognized Destination:

N/A

Multicast Frames Rcv'd:

N/A Data Overrun:

N/A

Multicast Frames Sent:

N/A User Buffer Unavailable:

N/A

Frames Sent, Deferred:

N/A System Buffer Unavailable:

N/A

Unsupported parameters show N/A.

Sets the server description string.

SET SERVEr DEScription <description-string>

Enter the description for <description-string>.
The factory default value is

Silex MNS-300EM

7-3. SH SERVEr CO

7-4. SET SERVEr DEScription

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Похожие инструкции для MNS-300EM

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Похожие инструкции для MNS-300EM

Бренды по названию

Популярные бренды