Silex technology MNS-300EM Скачать руководство пользователя страница 72

Страница: 72 / 134

MNS-300EM Command Manual

6-2-7. SET PORT S1 ECPORT

Specifies the port number for remote connection to use when E-Cable is enabled.

SET PORT S1 ECPORT <port>

Specify the port number for <port>.
When 0 is given, no data will be sent.

The factory default value is

6-2-8. SET PORT S1 ECRADDR

Sets the primary/secondary IP address of E-Cable destination.
This setting is valid for UDP mode only.

SET PORT S1 ECRADDR <index> <aa.bb.cc.dd>

index

: When the index value is set to 0, the primary address is set.
When not 0, the valid range is 1 to (n-1), where "n" is the value configured by

SET PORT S1 ECNHOST

. When "n" is 1, only the primary address can be set.

aa.bb.cc.dd

: Specifies the IP address of E-Cable destination.
When 0.0.0.0 or 0 is given, no data will be sent.

The factory default value is

0.0.0.0

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды