Silego GreenPAK SLG46140 Скачать руководство пользователя страница 154

Страница: 154 / 170

000-0046140-111

Page 153 of 169

SLG46140

reg<603>

PWM/DCMP1 mode selection

0: PWM output duty cycle down to 0% and DCMP

out=1 if A>B

1: PWM output duty cycle up to 100% and DCMP

out=1 if A>=B

reg<605:604>

PWM1 dead band zone control

00: 10 ns

01: 20 ns

10: 40 ns

11: 80 ns

reg<607:606>

PWM/DCMP1 positive input source selection

00: ADC

01: 8LSBs SPI

10: FSM1[7:0]

11: reg1

reg<609:608>

PWM/DCMP1 negative input

00: FSM1[7:0]

01:regs from MUX controlled by matrix_out[77:76]

10: 8MSBs SPI

11:FSM0[7:0]

PWM/DCMP 0

reg<611>

PWM/DCMP0 function selection

0: PWM

1: DCMP. when in PWM mode, OUTN0 is pwm0's

negative output. when in DCMP mode, OUTN0 is

dcmp0's match output

reg<612>

PWM/DCMP0 turn on by register

0: disable

1: enable

reg<613>

PWM/DCMP0 clock inversion

0: disable

1: enable

reg<614>

PWM/DCMP0 mode selection

0: PWM output duty cycle down to 0% and DCMP

out=1 if A>B,

1: PWM output duty cycle up to 100% and DCMP

out=1 if A>=B.

reg<616:615>

PWM0 dead band zone control

00: 10 ns

01: 20 ns

10: 40 ns 1

1: 80 ns

reg<618:617>

PWM/DCMP0 positive input source selection

00: ADC

01: 8MSBs SPI

10: FSM0[7:0]

11: regs from MUX controlled by matrix_out[77:76]

reg<620:619>

PWM/DCMP0 negative input

00: FSM0[7:0]

01:reg0

10: 8LSBs SPI

11:FSM1[7:0]

PWM/DCMP or DAC Data

reg<628:621>

reg0, 8 bits NVM data to PWM/DCMP or DAC input

data

reg<636:629>

reg1, 8 bits NVM data to PWM/DCMP or DAC input

data

reg<644:637>

reg2, 8 bits NVM data to PWM/DCMP or DAC input

data

reg<652:645>

reg3, 8 bits NVM data to PWM/DCMP or DAC input

data

reg<653>

power down sync to clock and output state control in

power down mode

0: power down is not synchronized with clock, and

output reset to 0 when PWM/DCMP is power down,

1: power down is synchronized with clock, when

PD=0, the clock is enabled after 2 clock cycles, while

when PD=1, the clock is gated immediately. and the

output is kept at current state when PD=1.

SPI

Register Bit

Address

Signal Function

Register Bit Definition

Содержание GreenPAK SLG46140











































































































































































Результаты поиска

Содержание GreenPAK SLG46140

Отзывы:

Silego GreenPAK SLG46140, Руководство пользователя, Страница: 154 / 170

Результаты поиска

Содержание GreenPAK SLG46140

Отзывы: