manualshive.com logo in svg

Sigineer Power MS6048D, Руководство пользователя

Поделиться
Скачать
Sigineer Power MS6048D Скачать руководство пользователя страница 26

                                                                                                                          www.sigineer.com 

 

24

 

(Default Display Screen) 

①

  AC Input frequency 

②

  Output frequency 

③

  Load power in VA 

④

  PV energy sum in KWH 

⑤

  Battery percentage 

⑥

Warning or Fault code 

 

 

 

①

  AC Input current 

②

  Output current 

③

  Load percentage 

④

  PV input current 

⑤

  Battery charging current 

⑥

Warning or Fault code 

 

 

 

①

  AC input power in Watts 

②

  Inverter temperature 

③

  Load power in Watts 

④

  PV energy sum in KWH 

⑤

  Battery percentage 

⑥

Warning or Fault code 

   

 

Firmware Version of Inverter PCB and MPPT 
PCB 
  (CPU1: 040-00-b21; CPU2:041-00-b21) 

 

Time 
(15:20:10, December 15, 2018) 

 

 
The LCD will display different inverter status when the up or down button is pressed. 
The last page of LCD shows the software version of the inverter PCB. There are 8 digits. 
If the MPPT PCB is not activated, it will display 000-00-000. 
When the LCD is switched to a new page, the LCD will return to the default home screen in 5 minutes 
without operation. 
When the LCD enters the setting page, the LCD will return to the default home screen in 2 minutes without 
operation. 
 
 
Operating Mode Description 

Содержание MS6048D

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды