Siemens TX-I/O Скачать руководство пользователя страница 34

Страница: 34 / 94

34 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

4.5.5

BOPowerDownValue

Parameter for representation of the backup value that becomes valid when



the device takes on the status PowerDown

and



the parameter [PowerDownModeAC24] = VALUE.

Possible values

INACTIVE
ACTIVE

4.5.6

Display

Defines the meaning of the display color.

As a result, a specific LED color is assigned to each meaning.

Parameter type: [DisplayEnum]

Possible values

Description

Normal

LED is lit green

Alarm

LED is lit red

Service

LED is lit yellow

Note



This parameter is used to assign a LED color to a signal type. After the

configuration, the color remains permanently assigned.
It is expressly

not

intended for use in combination with the status of the process

value.

4.5.7

Enabling Local Override

Enable/disable the module key Up/Down for the "Local override" function.

The general switching behavior (for enabled local overriding) is defined as follows:



Switch from automatic to local override (manual):

The current process value is valid until a new manual command is issued.



Switch from local override to automatic:

The automatic process value becomes valid once the Profinet I/O controller
writes a new value.

Possible values

Description

Selected Enabled
Not selected

Disabled

The module

TXM1.6RL

('light module') does not support

local overriding.

Definition,

addition

Definition,

addition

Mapping for multicolor
LEDs

Only module TXM1.8D

Definition,

addition

Switching behavior

Restriction

Содержание TX-I/O































































































Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды

Siemens TX-I/O, Руководство пользователя

Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды