Siemens TX-I/O Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 94

background image

41 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

4.8

Multistate Output Mapping (Static)

MO(X)_STATIC_(X)CHA_(X)

(SIMATIC Manager hardware catalog)

Parameter for mapping the multistate process value to a specific number of output
channels.

We distinguish between three different [MO(n)_Static] function types. The following
table shows the channels in regard to function and representation in the SIMATIC
Manager hardware catalog:

Channels

Relevant submodules,
representation in the Simatic Manager hardware catalog

2-channel MO2_Static_2Cha_St1

MO2_Static_2Cha_St2

3-channel MO3_Static_3Cha_St1

MO3_Static_3Cha_St2
MO3_Static_3Cha_St3

4-channel MO4_Static_4Cha_St1

MO4_Static_4Cha_St2
MO4_Static_4Cha_St3
MO4_Static_4Cha_St4

Important

These function groups must be inserted in the subslots



without any changes to the order

and



in direct succession to each other.

4.8.1

Mapping Function 1:n

Parameter for mapping the multistate process
value to a single active output channel in
accordance with the parameter [MappingTable].

Only a single output can ever be active.

In the case of an invalid [MOValue] (i.e., no
corresponding value was found in
[MappingTable],



a quality error message (Reliability) is

generated [Quality = MULTISTATE_FAULT]



a backup value becomes valid according to the

value in [BackupMode].

Duplicate assignments in the [MappingTable]

are not detected by the I/O function. Only the
value that is found first determines the output
channel.

Representation

Definition,

addition

Function and
representation of the
channels

Definition,

addition

«
...
39
40
41
42
43
...
»

Содержание TX-I/O































































































Отзывы:

Нет отзывов

Похожие инструкции для TX-I/O

AF-600 FP Series

Бренд: GE Страницы: 7

Бренд: EasyPro Страницы: 8

Бренд: Easylift Страницы: 127

Бренд: The Handy Страницы: 4

Бренд: Aiphone Страницы: 32

Бренд: probst Страницы: 33

Бренд: Keurig Страницы: 6

Бренд: Aiphone Страницы: 2

Бренд: Senju Sprinkler Страницы: 8

Бренд: Fender Страницы: 51

evolution avisa

Бренд: Fermax Страницы: 30

Бренд: Ravaglioli Страницы: 68

SAM GENERATION 2

Бренд: HALE Страницы: 12

Бренд: TCS Страницы: 12

Бренд: iCONNECT Страницы: 20

Reflex Wheel-X 50 050 0030

Бренд: Carson Страницы: 52

Бренд: Nussbaum Страницы: 72

Бренд: FISCHER Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды