Siemens TX-I/O Скачать руководство пользователя страница 19

Страница: 19 / 94

19 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Engineering

23.09.2010



Up to 64 TX-I/O modules can be connected with a Profinet BIM at the same

time.

3.3.1

Module Configuration

The TX-I/O modules supported by the Profinet BIM are found in the hardware
catalog under the

TXB1.Profinet

submodule.

Please observe the following points when working on the module configuration:



Recommendation:

Keep the addresses identical with the parameterized

SIMATIC input and output addresses.



---> TX-I/O module addresses must agree with the number of the slot in which
they are located and

---> TX-I/O modules must be inserted in the slot whose number matches
the corresponding TX-I/O module address.



Slots suitable for accepting TX-I/O modules are marked in

green



A TX-I/O module can be deleted at any time with the

Del

button.

In doing so, you

must reply to a security prompt (example for a TXM1.6R module):

Upper window section: click the required

submodule

Opens the TX-I/O module in the lower window section.

Hardware catalog: insert the required

TX-I/O module

by drag&drop.

When dragging the object, the free slots are displayed in

green

. After

dropping the module, a window similar to the one shown below appears
(extract, with TXM1.6R as an example).

Save

We recommend saving at meaningful intervals, but always for each

inserted TX-I/O module.

Before you start

Procedure

Содержание TX-I/O































































































Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды

Siemens TX-I/O, Руководство пользователя

Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды