Siemens TX-I/O Скачать руководство пользователя

Страница: 33 / 94

33 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

4.5

Binary Output (Bistable)

BO_BISTABIL

(SIMATIC Manager Hardware catalog)

Parameter for converting a binary process value to the module-specific switching
value.

Unlike the OnOff binary output function, the following points apply to this output:



The behavior can be defined if PowerDown (AC) is detected. In this regard,
bistable relays are used that retain their status during PowerDown.



The activation of the backup value can be delayed if a MasterDown status is
detected.

4.5.1

Backup Mode

Function for control of the behavior of the function when changing to the
"MasterDown" status.

Possible values

Description

Process value = INACTIVE, 0 (Off)

VALUE

Specific value of the parameter [BOBackupValue]

KEEP

Save the last active process value

4.5.2

BO Backup Value

Parameter – type [BinaryValueEnum] – that represents the backup value and
becomes valid in the following cases:



a change in status to "MasterDown"

and



the parameter [BackupMode] = VALUE

Possible values

Description

ACTIVE

Binary output is active.

INACTIVE

Binary output is inactive.

4.5.3

BackupDelay

Parameter for defining a delay upon activation of a backup value (according to the
[BackupMode]) after detection of a MasterDown.

Value range

Unit

0...65535 0.1

4.5.4

PowerDownModeAC24V

Parameter for defining the behavior following the detection of a MasterDown.

Possible values

Description

Process value = INACTIVE, 0 (Off)

VALUE

Specific value of the parameter [BOBackupValue]

KEEP

Save the last active process value

Representation

Definition,

addition

Definition,

addition

Definition,

addition

Definition,

addition

Definition,

addition

Содержание TX-I/O































































































Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды

Siemens TX-I/O, Руководство пользователя

Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды