Siemens TX-I/O Скачать руководство пользователя страница 5

Страница: 5 / 94

5 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

About this Document

23.09.2010

Module Data...........................................................................................73

7.1

General ...................................................................................................73

7.2

TXM1.8D .................................................................................................74

7.2.1

Process Data Channel Mapping .............................................................74

7.2.2

Counter Value Default Channel Mapping................................................74

7.3

TXM1.16D ...............................................................................................75

7.3.1

Process Data Channel Mapping .............................................................75

7.3.2

Counter Value Default Channel Mapping................................................76

7.4

TXM1.8U, TXM1.8U-ML TXM1.8X, TXM1.8X-ML .................................76

7.4.1

Process Data Channel Mapping .............................................................76

7.4.2

Local Override Channel Mapping ...........................................................77

7.4.3

Counter Value Default Channel Mapping................................................78

7.5

TXM1.6R, TXM1.6R-M, TXM1.6RL ........................................................79

7.5.1

Process Data Channel Mapping .............................................................79

7.5.2

Local Override Channel Mapping ...........................................................81

7.6

TXM1.8P .................................................................................................81

7.6.1

Channel Process Data Channel Mapping...............................................81

7.6.2

Local Override Channel Mapping ...........................................................82

Hardware................................................................................................83

8.1

Installing the Devices ..............................................................................83

8.2

Replacing a Module ................................................................................84

8.3

Labeling and Addressing Devices...........................................................85

8.3.1

Flow and Allocation of the Labelling........................................................85

8.3.2

Labeling the I/O Modules ........................................................................85

8.3.3

Addressing ..............................................................................................86

8.4

Technical Data.........................................................................................87

8.5

Connections ............................................................................................89

Index ................................................................................................................91

Содержание TX-I/O































































































Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды

Siemens TX-I/O, Руководство пользователя

Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды