Siemens TS2000 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 65

Siemens TS2000 Скачать руководство пользователя страница 42

TS2000 Service Manual

RD7409290-0 Rev. F

5-4

5.3 Replacing the PSB Board (Mounted)

1. Turn off the power system.

2. Disconnect the probes from the PSB.

3. Unscrew the four screws securing the PSB asembly to the TSP.

4. Disconnect the data cable from the PSB.

5. Remove the PSB assembly.

6. Reconnect the data cable to the PSD.

7. Place the new PSB assembly and secure it to the TSP with the four

screws.

5.4 Replacing the Isolated I/O card

5.4.1 Replacing Card

1.

Perform steps 1-9 from the section "Replacing the
Computer". (See instructions above.)

2.

Slide the computer out carefully.

3.

Unscrew the I/O card (one screw) from the Computer
connection panel. The I/O card is located in the third slot
from the bottom. Remove the I/O card gently.

4.

Check the setup of the I/O card It should be COM2 -IRQ3
and LPT2.

5.

Push the new I/O card into place gently (the third slot
from the bottom).

6.

Attach the I/O card to the Computer connection panel by
replacing and tightening the screw.

7.

Slide the computer back into place.

8.

Perform steps 11-20 from the section "Replacing the
Computer" (see above instructions).

9.

Connect the system to the electrical outlet and turn the
system on; the system is ready for use.

SPB7-520.840.01.01.02

«
...
40
41
42
43
44
...
»

Содержание TS2000


































































Отзывы:

Нет отзывов