manualshive.com logo in svg

Siemens TS2000, Руководство по обслуживанию, Страница: 39 / 65

Поделиться
Скачать
Siemens TS2000 Скачать руководство пользователя страница 39

 

5-1

5.  PARTS REPLACEMENT 

NOTE: 

 

 

The replacement of the parts described in this 
section must be followed by a functional test.  See 
section 7.4. 
Each intervention (replacement or repair) must be 
recorded in the “records of service visits” in the 
manual. 

 

5.1  Replacing the Computer 

1. 

Turn the system power off.  Disconnect any cables that have 
access to the electrical outlet. 

2. 

 Disconnect the main power connection, the power to the modem, 
the power cables from the monitor, the cables from the PM board, 
and the probe cables from the PSB.   

3. 

Open the back of the case and remove the monitor, mouse, 
keyboard, printer and modem cables from the computer and move 
the case from the cart to a table. 

4. 

Open the upper cover of the main system enclosure (Main 
Console) by unscrewing the four screws (two on each side). 

5. 

Remove the bottom of the main system enclosure by unscrewing 
the four screws (two on each side) that secure it in place. 

6. 

From inside the system, unscrew the three screws that are located 
on the upper front panel. 

7. 

Turn the whole system over and unscrew the three screws that are 
located on the inside of the bottom front panel. 

8. 

Turn the system right side up again. Disconnect the front panel 
switch (the connector that is on the right side of the T1 
transformer). Even though the switch is disconnected, it should 
remain in the "OFF" position. 

9. 

Remove the entire front panel. There are two edges on the sides of 
the front panel; unscrew the four screws that secure it (two on the 
bottom and two on the top). These screws can be accessed from 
the front of the main system enclosure. 

10. 

Disconnect all the cables from the Computer connection panel 
(located in the back of the system).  This includes computer power 
and communication cables. 

SPB7-520.840.01.01.02

Содержание TS2000


































































Отзывы:

Нет отзывов