Siemens SIRIUS 3RW52 Скачать руководство пользователя страница 203

Страница: 203 / 258

Maintenance and servicing

10.4 Restore factory setting

SIRIUS 3RW52 Soft Starter
Equipment Manual, 04/2020, A5E35630451002A/RS-AE/005

203

10.4.3

Restoring the factory settings with the MODE and RESET / TEST keys

Requirements

Ⴠ

3RW52 soft starter from firmware version V2.0

Ⴠ

Make sure that the motor is switched off and that you do not start the motor while

restoring the factory settings. To ensure the quickest and most fault-free restoration of the

factory setting, it is recommended that you disconnect the main voltage

(operating voltage) at the 3RW52 soft starter.

Ⴠ

The 3RW5 communication module must be isolated from the 3RW52 soft starter.

Video instructions

Video instructions can be found in SIOS

(

https://support.industry.siemens.com/cs/ww/en/view/109778874

Procedure

Start the restoration of the factory settings by pressing the MODE key longer than

2 seconds until the STATE / OVERLOAD LED flickers green.
Press and hold the MODE key.

Simultaneously press the RESET / TEST key down for at least 10 seconds.
After 2 seconds, the STATE / OVERLOAD LED begins to illuminate red.
After 10 seconds the STATE / OVERLOAD LED goes out and switches back to

displaying the motor operating state (e.g. flashing yellow if there is no main voltage

(operating voltage)).

Release the MODE and RESET / TEST keys.

Result

The factory setting of the 3RW52 soft starter is restored.
Note the effects of the factory settings (Page 199).

Содержание SIRIUS 3RW52



































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW52

Отзывы:

Похожие инструкции для SIRIUS 3RW52

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW52, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SIRIUS 3RW52

Отзывы:

Похожие инструкции для SIRIUS 3RW52

Бренды по названию

Популярные бренды