Siemens SIRIUS 3RW52 Скачать руководство пользователя страница 172

Страница: 172 / 258

Messages and diagnostics

9.2 LED display

SIRIUS 3RW52 Soft Starter

172

Equipment Manual, 04/2020, A5E35630451002A/RS-AE/005

9.2.3

STATE / OVERLOAD LED

"ST/OL" LED Status of the

3RW52 soft starter

Motor operating state

Lights up

green

Operation

The ramp up time comes to an end and the motor is

running.

Flashes

green

Starting or stopping

time active

Motor is ramping up or ramping down.

Off

Stop

Motor is switched off but might still be rotating.

Motor is ready to start.

Flashes

yellow

Stop - not ready to start

Motor is switched off but might still be rotating.

Motor is not ready to start. An ON command will cause
an error while at least one of the starting conditions is
not fulfilled, e.g.:
–

Supply voltage of motor missing.

Flashes

alternately

green / yellow

Operation with motor

overload warning

Motor has started up and is running.
A motor overload warning exists, e.g.:

Motor is too hot

Lights up

yellow

Stop with motor

overload warning

Motor has decelerated to zero speed and shut down.
A motor overload warning exists, e.g.:

Motor is too hot

Flashes red

Stop with motor

overload error

Motor has decelerated to zero speed and shut down due to

an overload error.
A motor overload error exists, e.g.:

Motor is too hot

Temperature sensor wire break

Temperature sensor short circuit

Содержание SIRIUS 3RW52



































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW52

Отзывы:

Siemens SIRIUS 3RW52, Руководство по эксплуатации оборудования, Страница: 172 / 258

Результаты поиска

Содержание SIRIUS 3RW52

Отзывы: