Siemens SINAMICS G120 PM240P-2 страница 39 Скачать руководство пользователя

Страница: 39 / 106

Connecting

4.1 Permissible line supplies

Power Module PM240P-2
Hardware Installation Manual, 06/2020, A5E37800827C AD

4.1.2

TT line system

In a TT line system, the transformer ground-

ing and the installation grounding are inde-

pendent of one another.
There are TT line supplies where the neutral

conductor N is either transferred – or not.

Note
Operation in IEC or UL systems
For installations in compliance with IEC, operation on TT line systems is permissible. For

installations in compliance with UL, operation on TT line systems is not permissible.

Operating converter on a TT line system

●

Converter with integrated or external line filter:
–

Operation on TT line systems with grounded neutral point permissible.

–

Operation on TT line systems without grounded neutral point not permissible.

●

Converter without line filter:
–

Operation on all TT line systems permissible.

Содержание SINAMICS G120 PM240P-2











































































































Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды

Siemens SINAMICS G120 PM240P-2, Руководство по установке

Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды