Siemens SINAMICS G120 PM240P-2 страница 73 Скачать руководство пользователя

Страница: 73 / 106

Technical data

6.7 Restrictions for special ambient conditions

Power Module PM240P-2
Hardware Installation Manual, 06/2020, A5E37800827C AD

Permissible line supplies dependent on the installation altitude

●

For installation altitudes ≤

2000 m above sea level, it is permissible to connect the

converter to any of the line supplies that are specified for it.

●

For installation altitudes 2000 m ... 4000 m above sea level, the following applies:
–

Connection to a TN line system with grounded neutral point is permissible.

–

TN systems with grounded line conductor are not permitted.

–

The TN line system with grounded neutral point can also be supplied using an

isolation transformer.

–

The phase-to-phase voltage does not have to be reduced.

Note

Using Power Modules connected to TN line supplies with voltages ≥

600 V for installation

altitudes 2000 m … 4000 m

For voltages ≥ 600 V, the TN line supply must have a grounded neutral point established

using an isolating transformer.

Содержание SINAMICS G120 PM240P-2











































































































Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды

Siemens SINAMICS G120 PM240P-2, Руководство по установке

Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды