Siemens SINAMICS G120 PM240P-2 страница 25 Скачать руководство пользователя

Страница: 25 / 106

Installing

3.2 EMC-compliant installation of a machine or system

Power Module PM240P-2
Hardware Installation Manual, 06/2020, A5E37800827C AD

Routing cables outside the control cabinet

●

Maintain a minimum clearance of 25 cm between cables with a high level of interference

and cables with a low level of interference.

●

Use shielded cables for the following connections:
–

Converter motor cable

–

Cable between the converter and braking resistor

–

Signal and data cables

●

Connect the motor cable shield to the motor enclosure using a PG gland that establishes

a good electrical connection.

Requirements relating to shielded cables

●

Use cables with finely-stranded, braided shields.

●

Connect the shield to at least one end of the cable.

Figure 3-4

Examples for EMC-compliant shield support

●

Attach the shield to the shield support directly after the cable enters the cabinet.

●

Do not interrupt the shield.

●

Only use metallic or metallized plug connectors for shielded data cables.

Содержание SINAMICS G120 PM240P-2











































































































Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды

Siemens SINAMICS G120 PM240P-2, Руководство по установке

Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды