Siemens SIMATIC NET S7-1200 Скачать руководство пользователя страница 27

Страница: 27 / 98

Installing, connecting up and commissioning

3.2 Warning overvoltage protection

CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02

3.2

Warning overvoltage protection

CAUTION

Protection of the external 24 VDC power supply
If power is supplied to the module over longer 24 V power cables or networks, the coupling

in of strong electromagnetic pulses onto the power supply cables is possible. This can be

caused, for example by lightning strikes or switching of higher loads.
The connector of the external 24 VDC power supply is not protected from strong

electromagnetic pulses. To protect it, an external overvoltage protection module is

necessary. A suitable device is, for example, the Dehn Blitzductor BVT AD 24V type no.

918 402 or comparable protective element.
Manufacturer:

DEHN + SÖHNE GmbH + Co. KG, Hans-Dehn-Str. 1, PO box 1640, D-92306 Neumarkt

3.3

Installing and commissioning the CP

Prior to installation and commissioning

WARNING

Read the system manual "S7-1200 Programmable Controller"
Prior to installation, connecting up and commissioning, read the relevant sections in the

system manual "S7-1200 Programmable Controller", refer to the documentation in the

Appendix.
When installing and connecting up, keep to the procedures described in the system manual

"S7-1200 Programmable Controller".

Configuration

One requirement for the commissioning of the CP is the completeness of the STEP 7 project

data (see below). You should also read the section "Configuration (Page 43)".

Содержание SIMATIC NET S7-1200



































































































Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды

Siemens SIMATIC NET S7-1200, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды