Siemens SIMATIC NET S7-1200 Скачать руководство пользователя страница 62

Страница: 62 / 98

Configuration

5.4 Configuring the telecontrol instructions

CP 1242-7

Operating Instructions, 09/2011, C79000-G8976-C247-02

●

TCON_phone for connections to SMS clients

●

TCON_WDC for connections to telecontrol servers or stations that can be reached via the

telecontrol server.

The parameter assignment of the connection description is made in a data block of the same

type as the SDT.

NOTICE

No optimized block access
When creating the data blocks, use the "Standard" option for block access.

Reserved bits are not displayed during configuration in STEP 7.

System data type TCON_ip_rfc for connections to IPv4 stations

This connection type is supported only on ISO-on-TCP connections to communications

partners with a fixed IP address. The CP must be configured for the "GPRS direct" mode.

Table 5- 1

Parameters of TCON_ip_rfc

Byte

Parameter

Data type

Initial value

Description

0 ... 1 InterfaceID

HW_ANY

Reference to the interface of the local CP 1242-7

(see STEP 7 > CP configuration > Telecontrol

interface > "Hardware identifier")

2 ... 3 ID

CONN_OUC

1...07FF

Reference to the GPRS connection. The ID is

assigned and must be unique within the CPU.
Here, the same value as that of the ID parameter of

the TC_CON instruction must be used.

ConnectionType

BYTE

W#16#0C

Protocol variant 12 (C

): ISO-on-TCP connection

ActiveEstablished

BOOL

Identifier for the type of connection establishment:



0: Passive connection establishment



1: Active connection establishment

RemoteAddress

IP_V4

IP address of the connection partner

6 ... 9 ADDR

Array [1...4] of

Byte

IP address of the relevant connection partner

10 ...

- reserved -

RemoteTSelector

TSelector

Remote T selector

12 ...

TSelLen

UINT

Length of the remote T selector "RemoteTSelector"

Содержание SIMATIC NET S7-1200



































































































Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды

Siemens SIMATIC NET S7-1200, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды