Siemens SIMATIC NET S7-1200 Скачать руководство пользователя страница 89

Страница: 89 / 98

Accessories

C.2 TS Gateway

CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02

Main and substitute TeleService gateway

If the requirements for availability are higher, you can install TS Gateway as the main or

substitute gateway. If the connection via the main system cannot be established, you can

establish the TeleService connection via the substitute system. In terms of the range of

functions, both systems are identical and do not monitor each other.

Requirements for TeleService with the TeleService gateway

The following requirements must be met for TeleService via a TeleService gateway:
●

Engineering station connected to a LAN or with Internet access
The engineering Station on which TeleService will be operated via GPRS requires STEP

7, version V11.0 SP1 or higher. For STEP 7 V11.0 SP1, support package "CP 1242-7"

(HSP0003001) is also required.
TeleService is started in the STEP 7 project that contains the remote station with the CP

1242-7.

●

SIMATIC S7-1200
–

CPU with firmware version as of V2.0

–

Communications processor CP 1242-7

●

PC for the TeleService gateway with:
–

DVD drive

–

Connection to LAN or Internet access for connecting to the engineering station

–

Internet access for connecting to the remote S7 station

–

Installation of the "TS Gateway" application
The software ships with the CP 1242-7 (see product DVD).

Содержание SIMATIC NET S7-1200



































































































Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды

Siemens SIMATIC NET S7-1200, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET S7-1200

Отзывы:

Похожие инструкции для SIMATIC NET S7-1200

Бренды по названию

Популярные бренды