Siemens SIMATIC HMI IPC577C Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

background image

Operating Instructions (compact)

1.8 Connecting

SIMATIC HMI IPC577C

20

Operating Instructions (Compact), 05/2009, A5E02368077-01

Note equipotential bonding

A low-impedance earth connection ensures that interference signals generated by external

power supply cables, signal cables or cables to the peripherals are safely discharged to

earth.
Required tool for equipotential bonding: TORX T20 screwdriver.

Steps for connecting the equipotential bonding
1. Connect the equipotential bonding (M4

threads) on the device (large surface, large-

area contact) with the protective earth

conductor of the cabinet or plant in which the

device is to be installed.

The minimum conductor cross-section may

not amount to less than 5 mm

2

.

1.8.3

Connecting the 100 - 240 V AC Power Supply

General connection information

Note the following in order to operate the device safely and according to regulation:

Note
Voltage range
The varying voltage power supply module is designed for operation on 100 to 240 V AC

networks. It is not necessary to adjust the voltage range.

NOTICE

Risk of damage
Do not connect or disconnect power and data cables during thunderstorms.

WARNING

Power supply network
The device is designed for operation on grounded power supply networks (TN networks to

VDE 0100, Part 300, or IEC 60364-3).
It is not designed for operation on ungrounded or impedance-grounded power networks (IT

networks).

«
...
18
19
20
21
22
...
»

Содержание SIMATIC HMI IPC577C





































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC HMI IPC577C

Бренд: R.V.R. Elettronica Страницы: 38

Бренд: Caimore Страницы: 23

ANT130LZ Series

Бренд: Aerotech Страницы: 52

PN/N3-4-XKV70-SK

Бренд: Eaton Страницы: 2

Бренд: TMG Страницы: 36

Бренд: Danfoss Страницы: 16

Бренд: Parker Страницы: 50

Allen-Bradley 6200P-NS3A1

Бренд: Rockwell Automation Страницы: 28

JSE.5-0104MAEAD

Бренд: BRUNEL Страницы: 7

Бренд: Artila Страницы: 25

Бренд: Kohler Страницы: 8

Бренд: LaserMech Страницы: 72

PARAPROJECT TROLLEY U40 WOL

Бренд: Parat Страницы: 11

Бренд: Jäger Страницы: 40

3B SCIENTIFIC U8497460

Бренд: ELWE Страницы: 12

Бренд: Wieland Страницы: 40

PACSystems RXi Series

Бренд: GE Страницы: 8

Бренд: Maggi Страницы: 339

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды