Siemens SIMATIC HMI IPC577C Скачать руководство пользователя страница 21

Страница: 21 / 36

Operating Instructions (compact)

1.8 Connecting

SIMATIC HMI IPC577C
Operating Instructions (Compact), 05/2009, A5E02368077-01

NOTICE

Permitted mains voltage
The permitted nominal voltage of the device must conform with local mains voltage.

NOTICE

Power disconnection
The mains connector must be disconnected to fully isolate the device from mains. Ensure

easy access to this area.
A master mains disconnect switch must be installed if the device is mounted in a switch

cabinet.
Always ensure free and easy access to the power inlet on the device or that the safety

power outlet of the building installation is freely accessible and located close to the device.

NOTICE

If a Compact Flash card is used in the device, be sure that the card is properly installed

before you connect it.

Note
Power factor correction
The power supply contains an active PFC (Power Factor Correction) circuit to conform to the

EMC guidelines.
Uninterruptible AC power systems (UPS) must supply a sinusoidal output voltage in the

normal and buffered mode when used with SIMATIC PCs with an active PFC.
UPS characteristics are described and classified in the standards EN 50091-3 and IEC

62040-3. Devices with sinusoidal output voltage in the normal and buffered mode are

identified with the classification "VFI-SS-...." or "VI-SS-....".

Содержание SIMATIC HMI IPC577C





































Результаты поиска

Содержание SIMATIC HMI IPC577C

Отзывы:

Похожие инструкции для SIMATIC HMI IPC577C

Бренды по названию

Популярные бренды

Siemens SIMATIC HMI IPC577C, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC HMI IPC577C

Отзывы:

Похожие инструкции для SIMATIC HMI IPC577C

Бренды по названию

Популярные бренды