Siemens SIMATIC HMI IPC577C Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 36

background image

Operating Instructions (compact)

1.8 Connecting

SIMATIC HMI IPC577C
Operating Instructions (Compact), 05/2009, A5E02368077-01

19

1.8.2

Connecting the 24 VDC power supply

To be noted before you connect the device

Note the following in order to operate the device safely and according to regulation:

WARNING

The device should only be connected to a 24 VDC power supply which satisfies the

requirements of safe extra low voltage (SELV). You will also have to connect a protective

conductor. The cable cross section has to match the short-circuit current of the 24 VDC

power supply so that the cable will not be damaged in case of a short circuit
Cable cross sections must range from a minimum of 1.3 mm² (AWG16) to a maximum of

3.3 mm² (AWG12).

NOTICE

The 24VDC power source must be adapted to the input data of the device.

NOTICE

If a CompactFlash card is used in the device, make sure that the card is seated correctly

before you connect it.

Connecting the devices

Steps for connecting the device to the 24 V DC power supply
1. Switch off the 24 V DC power source.
2. Connect the DC plug

(1) DC 24 V

(2) ground

(3) protective conductor

Power consumption

The power consumption at 24 V can be up to 90 W, depending on device.

«
...
17
18
19
20
21
...
»

Содержание SIMATIC HMI IPC577C





































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC HMI IPC577C

Бренд: ABB Страницы: 14

Бренд: Parker Страницы: 39

Бренд: Southern States Страницы: 36

Бренд: Schmalz Страницы: 36

Бренд: zitrek Страницы: 37

Guardmaster LRTS

Бренд: Allen-Bradley Страницы: 4

CNC PROVerXL4030

Бренд: Genmitsu Страницы: 49

Бренд: Leister Страницы: 56

Бренд: GBC Страницы: 17

Hyperion BarMaster 900

Бренд: Meech Страницы: 12

Бренд: Graco Страницы: 87

Бренд: M&R Страницы: 43

Бренд: ABB Страницы: 112

Бренд: ABB Страницы: 112

Бренд: ABB Страницы: 108

Бренд: ABB Страницы: 112

Бренд: ABB Страницы: 121

Бренд: ABB Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды