Siemens SIMATIC HMI IPC577C Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

background image

Operating Instructions (compact)

1.7 Installing/Mounting

SIMATIC HMI IPC577C
Operating Instructions (Compact), 05/2009, A5E02368077-01

15

1.7.4

Securing the Device with Screws

IP54 degree of protection

This degree of protection is ensured for screw mounting.

NOTICE

Control cabinet installation: Material strength at the mounting cut-out
Please ensure that the material strength at the mounting cut-out is a maximum of 6 mm.

Please follow the specifications for the dimensions in the section .
The degree of protection can only be guaranteed when the following requirements are met:

1. The material strength at the mounting cut-out must be at least 2 mm.

2. The deviation from the plane of the mounting cut-out in relation to the external

dimensions for an installed HMI device is ≤ 0.5 mm.

Note
Securing with screws is not possible with the 12" touch screen variant.

Required tool for fasting with screws: 7 mm drill

NOTICE

Only use the catalog-listed mounting material (order number 6AV7672-8KE00-0AA0) for

19" devices for screw mounting.

NOTICE

Risk of damage
Ensure that no metal cuttings enter the device when the holes are drilled. Cover the device

with film or when drilling, use removal by suction.

«
...
13
14
15
16
17
...
»

Содержание SIMATIC HMI IPC577C





































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC HMI IPC577C

Бренд: Zimmer Страницы: 2

Бренд: ABB Страницы: 106

BTL7-P511-M-P-S32/KA Series

Бренд: Balluff Страницы: 16

Бренд: Dr.X Works Страницы: 14

Бренд: A.B.S. Страницы: 30

BTL5-A11-M Series

Бренд: Balluff Страницы: 18

Бренд: Kitagawa Страницы: 32

Бренд: Huck Страницы: 14

Kwik-Way SVS II Deluxe

Бренд: Irontite Products Страницы: 52

Бренд: Tripp Lite Страницы: 8

Бренд: Rauch Страницы: 66

Moeller MFD-CP4-CO

Бренд: Eaton Страницы: 41

Бренд: Kipor Страницы: 44

Бренд: KSB Страницы: 78

Бренд: Moeller Страницы: 2

Бренд: Harrington Страницы: 25

Бренд: Larius Страницы: 14

Бренд: Virutex Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды