Siemens SIMATIC HMI IPC577C Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 36

background image

Operating Instructions (compact)

1.5 Accessories

SIMATIC HMI IPC577C

8

Operating Instructions (Compact), 05/2009, A5E02368077-01

1.5

Accessories

These accessories are not included in the product package.

Accessories

Order no.

2 GB Compact Flash card

6ES7648 - 2BF02 - 0XF0

4 GB CompactFlash card

6ES7648 - 2BF02 - 0XG0

8 GB CompactFlash card

6ES7648 - 2BF02 - 0XH0

Memory module 1 GB DDR3

6ES7648 - 2AH40 - 0AH0

Memory module 2 GB DDR3

6ES7648 - 2AH50 - 0AH0

Memory module 4 GB DDR3

6ES7648 - 2AH60 - 0AH0

Touch pen

6AV7672-1JB00-0AA0

Note
Replace CompactFlash card only with replacement card of the same product version.
Only SIMATIC PC CompactFlash cards with product version number 02 (ES 02) can be

used for this device.

1.6

Affixing Labeling Strips for Function Keys and Softkeys

Note
The following table applies only to devices with a key panel.

The control unit has two horizontal and two vertical keypads for the function keys and the

softkeys. Assign user specific functions to the keys as needed. You can mark these keys

with labeling strips. A4 films for creating the labeling strips are available as accessories.
Proceed as follows to affix the labeling strips:

«
...
6
7
8
9
10
...
»

Содержание SIMATIC HMI IPC577C





































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC HMI IPC577C

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: Daikin Страницы: 12

Бренд: Napoleon Страницы: 3

Бренд: Daikin Страницы: 52

Бренд: Fuji Electric Страницы: 39

Бренд: Whelen Engineering Company Страницы: 6

Бренд: CHART Страницы: 30

GAT Rotopack BAT

Бренд: Moog Страницы: 27

Бренд: Dynamic Displays Страницы: 29

Бренд: Aaeon Страницы: 97

Бренд: Hakko Electronics Страницы: 4

Бренд: Eaton Страницы: 12

Бренд: Micromeritics Страницы: 62

Бренд: ABB Страницы: 16

Бренд: Kval Страницы: 108

Бренд: HappyJapan Страницы: 364

Бренд: Gonbes Страницы: 6

Electrobloc EBL 208 S G

Бренд: Schaudt Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды