Siemens SIMATIC HMI IPC577C Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

background image

Operating Instructions (compact)

1.7 Installing/Mounting

SIMATIC HMI IPC577C

16

Operating Instructions (Compact), 05/2009, A5E02368077-01

Figure 1-4

Designated location for holes on the control unit

Rack installation

Steps for fastening the device with screws
1.  Follow the installation instructions.
2.  Carefully drill the respective holes in the control unit at the designed location from the rear.
3.  Working from the front, insert the device into the 19" rack.
4.  Secure the control unit by inserting suitable screws through the holes and attaching nuts.

Swivel arm installation

Steps for fastening the device with screws
1.  Follow the installation instructions.
2.  Carefully drill the respective holes in the control unit at the designed location from the rear.
3.  Working from the front, place the device onto the swivel arm.
4.  Secure the control unit by inserting suitable screws through the holes and attaching nuts.

Control cabinet installation

Steps for fastening the device with screws
1. Follow the installation instructions.
2. Drill suitable holes at the prepared installation cut-out in accordance with the specifications for L4

and L5, as shown at the dimensions in the mounting cut-out

3.  Carefully drill the respective holes in the control unit at the designed location from the rear.
4.  Working from the front, insert the device into the mounting cut-out.
5.  Secure the control unit by inserting suitable screws through the holes and attaching nuts.

«
...
14
15
16
17
18
...
»

Содержание SIMATIC HMI IPC577C





































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC HMI IPC577C

Бренд: National Instruments Страницы: 73

Бренд: TEC Страницы: 6

GED5000IL Series

Бренд: Zimmer Страницы: 52

Бренд: Eaton Страницы: 2

SnapTable PRO Hyper-Lite

Бренд: SWENSON SHEAR Страницы: 12

Бренд: Gabocom Страницы: 4

PowerPass 9PXTFMR5

Бренд: Eaton Страницы: 62

Z100-H642.15 S11W2

Бренд: Jäger Страницы: 52

Бренд: Panblast Страницы: 9

Бренд: maxam Страницы: 100

Бренд: VORON Страницы: 12

FlashPac LS-1130

Бренд: Excelitas Technologies Страницы: 13

Бренд: B&G Страницы: 30

Бренд: Eaton Страницы: 2

BTL5-A/C/E1-MSF-F Series

Бренд: Balluff Страницы: 16

Flexiguard 8530595

Бренд: DBI SALA Страницы: 16

Бренд: Moxa Technologies Страницы: 2

Бренд: YOKOGAWA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды