Siemens SIMATIC HMI IPC577C Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

Operating Instructions (compact)

1.7 Installing/Mounting

SIMATIC HMI IPC577C

14

Operating Instructions (Compact), 05/2009, A5E02368077-01

NOTICE

Control cabinet installation: Material strength at the mounting cut-out
Please ensure that the material strength at the mounting cut-out is a maximum of 6 mm.

Please follow the specifications for the dimensions in the section .
The degree of protection can only be guaranteed when the following requirements are met:

1. The material strength at the mounting cut-out must be at least 2 mm.

2. The deviation from the plane of the mounting cut-out in relation to the external

dimensions for an installed HMI device is ≤ 0.5 mm.

«
...
12
13
14
15
16
...
»

Содержание SIMATIC HMI IPC577C





































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC HMI IPC577C

Бренд: KegLand Страницы: 23

Бренд: IBASE Technology Страницы: 22

Бренд: AEMC instruments Страницы: 12

HIS-ML15-***E Series

Бренд: Hope Industrial Systems Страницы: 24

Tripod Turnstile

Бренд: ZKTeco Страницы: 10

FiberRunner QuikLock FR12X4

Бренд: Panduit Страницы: 2

Бренд: SAF Страницы: 20

Бренд: Goodwe Страницы: 33

Ford F-150 K9 Kennel

Бренд: D&R ELECTRONICS Страницы: 10

GQM22M5C2H620JB01 Series

Бренд: Murata Страницы: 25

Бренд: Nordson Страницы: 33

Бренд: SIGMATEK Страницы: 48

Бренд: NetterVibration Страницы: 21

TracStar 500 Series 3

Бренд: McElroy Страницы: 60

Бренд: Kval Страницы: 118

Бренд: Komatsu Utility Страницы: 302

Бренд: Global Страницы: 51

Бренд: Huawei Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды