Siemens MAMMOMAT Balance Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 62

Siemens MAMMOMAT Balance Скачать руководство пользователя страница 52

Compression system

MAMMOMAT Balance

SPB7-115.840.01 Page 52 of 62

Siemens AG

Troubleshooting Guide

Rev.02 10.04

Medical Solutions

Compression system

Introduction

The compression device of MAMMOMAT BALANCE consists of a drive motor MT3 with gear box

08883659

coupled to an electromagnetic clutch

08883634

.

To access drive motor, remove tube cover.
To access electromagnetic clutch remove tube cover and c-arm front plate.
Compression force is adjusted by means of current flowing in the electromagnetic clutch that also has
safety function.
Drive motor has current sensing circuit for speed reduction when compression plate gets in contact
with the breast.
For function description refer to Operator’s manual

SPB7-115.620.01…

Configuration of Maximum compression force

Maximum compression force of 150 N or 200 N is selected by means of

SW2

DIP3 =

ON

Max compression force 200N

Index number on the display will change accordingly to maximum force selected.

Calibration of Maximum compression force

Maximum compression force of 150 N or 200 N is calibrated by means of

SW1

DIP7 =

ON

Compression force calibration

Insert shifted compression plate

8383197

, position a bathroom balance on the table and a soft

cushion between plate and balance as alternate method, spring balance can be used.
Compression force can be adjusted changing the correction factor from 1 to 20 that will appear on the
display in place of compression force.
Correction factor can be changed by means of mAs [+] [-] pushbuttons.
To the lowest correction factor corresponds the highest compression force and vice versa.

Motor current detector

For proper functionality of plate speed reduction, motor current detector is factory calibrated.

Motor or clutch replacement

If motor or clutch are replaced take care of correct alignment between clutch surfaces.
Correct alignment is essential for compression force constancy and reproducibility.
After replacement check and eventually calibrate compression force.

«
...
50
51
52
53
54
...
»

Содержание MAMMOMAT Balance































































Отзывы:

Нет отзывов