Siemens MAMMOMAT Balance Скачать руководство пользователя страница 28

Страница: 28 / 62

Filament

MAMMOMAT Balance

SPB7-115.840.01 Page 28 of 62

Siemens AG

Troubleshooting Guide

Rev.02 10.04

Medical Solutions

Anode current calibration

•

General information

Tube anode current mA is calibrated, for each value of kV and each focal spot, by means of filament
current

Two levels of anode current

mAL

and

mAH

are defined for each focus.

mAH

is related to lower part of kV range and

mAL

to higher part of kV range or mAs range.

mAL

and

mAH

calibration is based on two similar but independent procedures.

•

Calibration by internal instrument

Before entering any calibration mode, it’s necessary to select the manual mode and a value of

mAs

equal to

for the

0.3 mm focus

and

for the

0.1 mm focus

In calibration mode, the following keys are active:

•

Focal spot selection

•

kV selection for whole values

•

filament current adjustment by mAs + / - push buttons.

The anode current related to each value kV for each focus can be found in the Tube calibration report.

To enter

mAH

current calibration set

DIP1 of

SW1

( PCB

01-170) = ON

Содержание MAMMOMAT Balance































































Результаты поиска

Содержание MAMMOMAT Balance

Отзывы:

Siemens MAMMOMAT Balance, Руководство по устранению неисправностей, Страница: 28 / 62

Результаты поиска

Содержание MAMMOMAT Balance

Отзывы: