Siemens MAMMOMAT Balance Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 62

Siemens MAMMOMAT Balance Скачать руководство пользователя страница 17

Troubleshooting

MAMMOMAT Balance

SPB7-115.840.01 Page 17 of 62

Siemens AG

Troubleshooting Guide

Rev.02 10.04

Medical Solutions

ALARM

AEC DETECTOR OVER EXPOSED

Code

A1

When

After pre exposure

Why

Breast and / or detector position is/ are wrong, part of detector was exposed to direct x-
ray beam.
Breast or phantom density was too low.

Action

Check for proper breast / detector positioning or thin phantom.

Note

Film must be replaced.
Delivered mAs are less than 1 mAs

ALARM

BREAST TOO DENSE

Code

A0

When

After pre exposure

Why

Breast density is too high and [p] value lower than limit selected during AEC calibration
Breast could have silicone prosthesis.
Refer to AEC calibration procedure for [p] lower limit calibration.

Action

Reduce breast density and check for AEC calibration with reference phantom.

Note

Film must be replaced.
Delivered mAs are less than 1 mAs

ALARM

LOW mAs SELECTION WITH AEC

Code

Mi

When

After exposure

Why

Could happen with magnification and small focus if grid table is used and breast is large or
very dense.
Can also happen for calibration problems or system malfunction.

Action

Evaluate operating conditions and eventually use One point mode with higher kV.

Note

Quite impossible with large focus, if happens check very carefully mA, kV, [r] and [o]
calibrations.

«
...
15
16
17
18
19
...
»

Содержание MAMMOMAT Balance































































Отзывы:

Нет отзывов