Siemens MAMMOMAT Balance Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 62

Siemens MAMMOMAT Balance Скачать руководство пользователя страница 13

Troubleshooting

MAMMOMAT Balance

SPB7-115.840.01 Page 13 of 62

Siemens AG

Troubleshooting Guide

Rev.02 10.04

Medical Solutions

Troubleshooting

o

If unit doesn’t switch ON refer to dedicated section of this manual.

o

If unit can be switched ON but: no Frame and no Icons appear on the screen and CPU reset
sequence is wrong , check voltages on CPU motherboard 03-188

o

If unit can be switched ON but: Frame and no Icons appear on the screen and CPU reset
sequence is wrong , check CPU 01-170.

o

If unit can be switched ON but: no Frame and no Icons appear on the screen and CPU reset
sequence is correct check keyboard 92-083, KEYBOARD CPU 03-181, cable CV0155 and
supply voltages onboard of KEYBOARD 92-083

If the unit is operative fault finding and troubleshooting is based on the followings:

1)  Operating or technical errors on display
2)  Technical menu
3)  Technical errors in Log file

1) Operating errors on Display

Operating errors on Display are described in the Operator’s manual SPB7-115.620.01….

For the technical aspects related to such alarms:

ALARM

GAS SPRING DEFECTIVE !

Code

Gs

When

Any time when unit is ON

Why

Gas spring has loosed it’s capacity to balance c-arm suspended masses

Action

For Gas Spring replacement refer to “Gas spring replacement” section in this document

For safety reasons unit can’t be operate d if Gas Spring is defective.
Alarm can’t be cleared

WARNING

«
...
11
12
13
14
15
...
»

Содержание MAMMOMAT Balance































































Отзывы:

Нет отзывов