Siemens MAMMOMAT Balance Скачать руководство пользователя страница 15

Страница: 15 / 62

Troubleshooting

MAMMOMAT Balance

SPB7-115.840.01 Page 15 of 62

Siemens AG

Troubleshooting Guide

Rev.02 10.04

Medical Solutions

ALARM

ABSENCE OF COLLIMATOR CONE

Code

When

Starting exposure

Why

Collimation plate is missing

Action

Insert collimation plate or check sensing microswitch and / or PCB 02-179 and
connection cable to main CPU CV0158

Note

Alarm goes OFF by itself if collimation plate is inserted

ALARM

CASSETTE NOT INSERTED

CASSETTE ALREADY EXPOSED

Code

Nc
Ce

When

Starting exposure

Why

Cassette is not inserted or already exposed or cassette sensing switches are defective

Action

Insert or replace cassette or check cassette sensing switches

Note

Alarm goes OFF by itself if cassette is inserted or removed.

ALARM

MIRROR POSITION ERROR

Code

When

Starting exposure

Why

Mirror is not out of field

Action

Check if mirror doesn’t move totally or partially for mechanical or electrical problems.
Mirror drive motor has position sensing switch inside that must switch ( audible click )
when is at 60 degrees with respect to the base plate.

Mirror driver is onboard of PCB 02179 connected to the main CPU by CV0158.

ALARM

FILTER POSITION ERROR

Code

When

Filter changes from Mo to Rh or vice-versa

Why

Position sensing switch is not closed

Action

Select manual mode, select filters several time to investigate if it’s mechanical or electric
problem.
Filter is driven by PCB 02-179.

Содержание MAMMOMAT Balance































































Результаты поиска

Содержание MAMMOMAT Balance

Отзывы:

Siemens MAMMOMAT Balance, Руководство по устранению неисправностей, Страница: 15 / 62

Результаты поиска

Содержание MAMMOMAT Balance

Отзывы: