manualshive.com logo in svg

Siemens MAMMOMAT Balance, Руководство по устранению неисправностей, Страница: 19 / 62

Поделиться
Скачать
Siemens MAMMOMAT Balance Скачать руководство пользователя страница 19

Troubleshooting

 

MAMMOMAT Balance 

SPB7-115.840.01      Page 19 of 62 

Siemens AG 

Troubleshooting Guide 

Rev.02        10.04 

Medical Solutions  

 

Fault 

CPU fuses F2 or F4 

 

Action 

Replace fuse  
 

 
 

Fault 

Filament 92-073     >> FAIL << 

 

Action 

1) check LED status of PCB 92-073 
2) if problem persists after having switched the Unit off and on again, verify the integrity of 
fuses F1 F2 PCB 92-073 and of filaments by an ohmmeter. 
3) if Alarm Code is T2 it was generated during preparation, check for eventual corruption 
of filament calibration values  
Check also calibration of Over-current and Over-voltage protection circuits. 
4) if Alarm Code is R2 it was generated during exposure check calibration of Over-current 
and Over-voltage protection circuits. 
5) if in doubt that filament board safety circuits are not recognized by CPU, they can be 
simulated by means of jumpers on the flat cable CV0173.  
 

 

 
 
 
 

 
 

Fault 

Rotating anode 92-074     >> FAIL << 

 

Action 

1) check LED status of PCB 92-074 
2) if problem occurs when the unit is in stand by check that flat cable CV174 connecting 
PCB 92-074 and PCB 01-170 has been correctly seated. Also check fuses  F1 and F3 of  
PCB 92-074 
3) if problem occurs in preparation error code is T1 check for line voltage, protection 
circuit calibration of PCB 92-074,  voltage across shift capacitors C5 and C6  that typically 
is about 120 Vac ( 50hz) during anode running.  If voltage is lower shift capacitor is 
probably defective. For capacitor voltage check, protection circuit has to be disabled. 
4) if problem occurs during exposure, error code is R1 check the same as above point 3 
5) alarm can also occur due to tube overheating when internal thermo switch opens. 
6) if in doubt that starter board safety circuits are not recognized by CPU,  they can be 
simulated by means of jumpers on CN5 PCB 01-170 or flat cable CV0174.  
 
 
 

 

 

 

CN5 

Содержание MAMMOMAT Balance































































Отзывы:

Нет отзывов