Siemens i-3 Скачать руководство пользователя страница 10

Страница: 10 / 80

Chapter 3

Control Input

Mounting bracket

The mounting bracket is a “C” shape
steel plate that screws into the P1
panel mounting rails. This bracket holds
the controller.

I/O controller box

Removing the communication
interface door

The communication interface door
provides access to the communication
interface section without removing the
entire cover. Use the door handle shown
in

Figure 3.1

to remove and install

the door.

Removing the cover

Them I/O Controller cover must be removed
to access the input wiring section. Follow
the step-by-step instructions below to
remove the cover:

1. Disconnect and lock off all power

sources supplying this panel.

2. Remove P1 Panel trim and deadfront.
3. Remove the cover screws (4 total)

located as shown on

Figure 3.1

remove the cover.

DANGER

Hazardous voltage.
Will cause death or
serious injury.

Keep out.
Qualiﬁ ed personnel only.
Disconnect and lock off all
power before working on
this equipment.

Door Handle

“C” shape
mounting bracket

Figure 3.1

I/0 Controller Communication Interface Door

Communications
interface door
(shaded )

Controller
mounting screws (4)

Cover screws (4)

Содержание i-3

















































































Результаты поиска

Содержание i-3

Отзывы:

Похожие инструкции для i-3

Бренды по названию

Популярные бренды

Siemens i-3, Руководство пользователя

Результаты поиска

Содержание i-3

Отзывы:

Похожие инструкции для i-3

Бренды по названию

Популярные бренды