Siemens FLENDER PLANUREX 2 PBUC Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 54

background image

BA 9213 en 03/2012

3.

Safety instructions

Entry to the gear unit and its add-on components is not permitted!
Caution! Risk of falling!

Any changes on the part of the user are not permitted. This applies equally to safety
features designed to prevent accidental contact.

3.1

Obligations of the user

•

The operator must ensure that everyone carrying out work on the gear unit has read and understood
these instructions and is adhering to them in every point in order to:

─ avoid injury or damage.

─ ensure the safety and reliability of the unit.

─ avoid disruptions and environmental damage through incorrect use.

•

During transport, assembly, installation, dismantling, operation and maintenance of the unit, the
relevant safety and environmental regulations must be complied with at all times.

•

The gear unit must be operated, maintained and/or repaired only by authorised, properly trained and
qualified personnel.

•

The outside of the gear unit must not be cleaned with highpressure cleaning equipment.

•

All work must be carried out with great care and with due regard to safety.

All work on the gear unit must be carried out only when it is not in operation.
The drive unit must be secured against being switched on accidentally (e.g. by locking
the key switch or removing the fuses from the power supply). A notice should be
attached to the start switch stating clearly that work is in progress.

•

No electrical welding work must be done at all on the drive.
The drives must not be used as an earthing point for welding operations. Toothed parts and bearings
may be irreparably damaged by welding.

•

A potential equalisation in accordance with the applying regulations and/or directives must be carried
out, if it is not possible to ensure, that voltages possibly occurring can be equalised by way of the
complete machinery, the machine frame, or the like. To this purpose free threaded holes on the gear
unit must be used.
If no threaded holes for earth connection are available on the gear unit, other appropriate measures
must be taken. This work must always be done by electrotechnical specialists.

If any inexplicable changes are noticed during operation of the gear unit, such as an
important increase in temperature or unusual noises, the drive assembly must be
switched off immediately.

Rotating drive components such as couplings, gearwheels, belt drives etc. must be
protected against accidental contact.

When the gear unit is incorporated in plant or machinery, the manufacturer of such
plant or machinery must ensure that the contents of these instructions are
incorporated in his own instructions.

«
...
11
12
13
14
15
...
»

Содержание FLENDER PLANUREX 2 PBUC Series























































Отзывы:

Нет отзывов

Похожие инструкции для FLENDER PLANUREX 2 PBUC Series

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Bang & Olufsen Страницы: 2

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренд: Yamaha Страницы: 29

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

IMPULSE 2 IT8026 Glute Master

Бренд: BM FITNESS Страницы: 18

Haymakers Hooimakers F80-350V

Бренд: Falcon Страницы: 38

Бренд: Lightronics Страницы: 6

Бренд: Neopost Страницы: 10

Бренд: KAM Страницы: 8

Бренд: Meyer Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды