Siemens FLENDER K DH Series Скачать руководство пользователя страница 92

Страница: 92 / 109

92 / 109

BA 5846 en 05/2015

Faults

Remedy

Causes

Increased temperature at the
bearing points.

Oil level in gearunit housing too
low or too high.

Oil too old.

Bearing is defective.

Oilsupply system defective.

Check the oil level at ambient
temperature. Top up or drain oil,
if necessary.

Check date of last oil change.
Change oil, if necessary.
See section 10.

Contact Customer Service.
Check and, if necessary,
replace bearings.

Check the oilsupply system.
Replace defective components,
if necessary. Consult operating
instructions for oilsupply system.

Increased vibration amplitudes
at the bearing points.

Bearing is defective.

Gears are defective.

Contact Customer Service.
Check and, if necessary, replace
bearings.

Contact Customer Service.
Check and, if necessary,
replace gears.

Exterior of gear unit is oiled up.

Inadequate sealing of housing
covers and/or joints.

Labyrinth seals oiled up.
Incorrect transport position.

Seal housing covers and/or joints.

Check oil filling.
Clean labyrinth seals. ?xx?

Oil leakage from the gear unit.

Inadequate sealing of housing
covers and/or joints.

Radial shaftsealing rings defective.

Pipework leaky.

Check and, if necessary, replace
seals.
Seal housing covers and/or joints.
Check sealing pressure;
if necessary, retighten screws.

Replace radial shaftsealing rings.

Check and, if necessary,
replace or seal.

Содержание FLENDER K DH Series














































































































Результаты поиска

Содержание FLENDER K DH Series

Отзывы:

Похожие инструкции для FLENDER K DH Series

Бренды по названию

Популярные бренды

Siemens FLENDER K DH Series, Руководство по сборке и эксплуатации

Результаты поиска

Содержание FLENDER K DH Series

Отзывы:

Похожие инструкции для FLENDER K DH Series

Бренды по названию

Популярные бренды