Siemens FLENDER K DH Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 109

Siemens FLENDER K DH Series Скачать руководство пользователя страница 24

BA 5846 en 05/2015

4.4.1.2 Interior preservation with "Castrol Tribol 1390 / 220"

Table 3:

Durability period and measures for interior preservation when using PGbased synthetic oil

Durability period

Preservative agent

Special measures

up to

6

months

Special anticorrosion oil
TRIBOL 1390

1)

None

up to

36

months

– Seal all holes on the gear unit.

– Replace the air filter or wetair filter with

a screw plug. (Replace the screw plug
with the air filter or wetair filter before
startup.)

– Seal the labyrinth seal on the output

shaft with adhesive tape. (Prior to
startup remove the adhesive tape.)

For storage periods longer than 36 months, renew the preservation (see item 4.4.1.3).

1)

Resistant to tropical conditions and sea water; maximum ambient temperature 50 °C

Note

The procedure for interiorpreservation treatment is described in section 7 (see item 7.3.1).

4.4.1.3 Represerving the interior of the gear unit in case of longer periods of storage

CAUTION

Risk of injury

Risk of injury to eyes or hands through chemically aggressive operating media.
Wear suitable protective glasses and protective gloves.
Remove any oil spillage immediately with a binding agent.

For storage periods longer than 24 months (see table 2) or 36 months (see table 3), the interior
preservation of the gear unit must be renewed. The following procedure is recommended:

•

Remove any dirt in the area of the inspection and/or assembly cover or that of the marked oilfilling
point.

•

Undo and remove the fastening screws of the inspection and/or assembly cover.

•

Remove the cover with the seal from the housing (the seal must not be damaged, it will be used again).

•

Place a suitable container under the oildrain point of the gearunit housing.

•

Unscrew the oildrain plug and/or open the oildrain cock and drain the used preservation oil into
a suitable container.

•

Dispose of the residue of the preservative oil in accordance with regulations.

•

Shut the oildrain cock and/or screw in the oildrain plug.

•

Fill the gear unit with "Castrol Alpha SP 220 S".
Determine the filling quantity according to the gearunit dimensions: length x width x height x 0.05.

NOTICE

Material damage

Corrosion possible through use of an unsuitable preservative agent.
Use special oil "Castrol Alpha SP 220 S" with additional anticorrosive agent (additive "S").

«
...
22
23
24
25
26
...
»

Содержание FLENDER K DH Series














































































































Отзывы:

Нет отзывов