Siemens FLENDER K DH Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 109

background image

BA 5846 en 05/2015

DANGER

Electrostatic discharge

Danger to life through ignition of any potentially explosive atmosphere through electrostatic discharge.
The coating must not carry an electrostatic charge.
The operator must ensure that highly effective mechanisms which can set up a charge in the coating are
safely avoided.

•

Removed safety equipment must be refitted prior to starting up.

•

Notices attached to the gear unit, such as rating plate and direction arrow, must always be observed.
They must be kept free from dirt and paint at all times. Missing plates must be replaced.

•

Screws which have been damaged during assembly or disassembly work must be replaced with new
screws of the same strength class and type.

•

Spare parts must be obtained from Siemens (see section 11, "Spare parts, customer service").

3.2

Special dangers and personal protective equipment

Depending on operating conditions, the surface of the gear unit may heat up or cool down to extreme
temperatures.

WARNING

Risk of burns

Risk of serious injury through burns on hot surfaces (> 55 °C).
Wear suitable protective gloves and protective clothing.

WARNING

Danger through low temperatures

Risk of serious injury through frost (pain, numbness, frostbite) on cold surfaces (< 0 °C).
Wear suitable protective gloves and protective clothing.

WARNING

Risk of scalding

Risk of serious injury through escaping hot operating media, when they are being changed.
Wear suitable protective gloves, protective glasses and protective clothing.

WARNING

Risk of eye injury

Small foreign matter such as sand or dust can get into the cover plates of the rotating parts and be thrown
back by these.
Wear suitable protective glasses.

«
...
14
15
16
17
18
...
»

Содержание FLENDER K DH Series














































































































Отзывы:

Нет отзывов

Похожие инструкции для FLENDER K DH Series

Бренд: Taber Страницы: 27

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: Haigh Страницы: 60

Бренд: tayco Страницы: 111

Бренд: Kellfri Страницы: 12

Бренд: RAPID REBOOT Страницы: 18

Бренд: MacDon Страницы: 170

Бренд: MacDon Страницы: 108

Бренд: MacDon Страницы: 108

Бренд: MacDon Страницы: 51

Бренд: MacDon Страницы: 104

Бренд: MacDon Страницы: 240

QUANTOFIX Relax

Бренд: Macherey-Nagel Страницы: 192

Бренд: MacDon Страницы: 182

Бренд: MacDon Страницы: 192

Бренд: MacDon Страницы: 53

Бренд: MacDon Страницы: 2

Бренд: Pahlen Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды