Siemens CU240S DP-F Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 232

background image

Commissioning

5.5 Commissioning using the BOP

Control Units CU240S

92

Operating Instructions, 07/2008 - FW 3.2, A5E00766042B AD

5.5.7

Series commissioning using the BOP

Upload and download a parameter set with a BOP

With a BOP a single parameter set can be uploaded from an inverter and then downloaded

into another inverter.
To copy a parameter set from one inverter to another, the following procedure should be

performed.

Upload a parameter set with a BOP

Prerequisites
●  An inverter with an appropriate parameter set is available (upload inverter)
●  Supply voltage is active for the upload inverter
●  The upload inverter is in "Ready to Run".

Parameter

Description

Setting

Fit the BOP to the Inverter - for the parameter set to be uploaded, perform the following

steps:

P0003 = 3

User access level*

1: Standard: Allows access into most frequently used parameters (default)

2: Extended: Allows extended access e.g. to inverter I/O functions

3: Expert: For expert use only

P0010 = 30

Commissioning parameter*

0: Ready (default)1: Quick commissioning

2: Inverter

30: Factory setting, parameter transfer

95: Safety commissioning (for CUs with fail-safe functions only)

P0802 = 1

Transfer data from EEPROM

0: Disabled (default)

1: Start BOP transfer

2: Start MMC Transfer
While the upload is active "bUSY" will be displayed on the BOP and the inverter will not react

to any commands.

If the upload has been completed successfully, P0010 and P0802 will be set to 0 and the

BOP display will return to normal.

If the upload has failed, F00051 (failure while accessing EEPROM), F00055 (failure while

saving parameter on BOP) or F00057 (BOP fault) will be displayed.

In this case attempt another upload or perform a power-cycle to confirm F00051.

After a successful upload disconnect the BOP from the upload inverter to connect it to the

download inverter.

«
...
90
91
92
93
94
...
»

Содержание CU240S DP-F









































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CU240S DP-F

Бренд: Radio Shack Страницы: 52

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: Kamstrup Страницы: 36

Бренд: JFA Electronicos Страницы: 29

FEBCO 860 Small Series

Бренд: Watts Страницы: 12

Бренд: Bardiani Valvole Страницы: 54

Бренд: Parker Страницы: 478

Бренд: +GF+ Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды