Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 8

Страница: 8 / 62

Contents

SIM 1-2

C79000-G8976-C215-01

4.2

Power-saving Isolation with Optocouplers......................................................... 47

4.2.1

Internal Pulse Duration Modulator ..................................................................... 47

4.2.2

Internal Pulse Duration Demodulator ................................................................ 48

4.2.3

External Dynamic Signal Evaluation.................................................................. 51

4.3

Signal Assignment ............................................................................................. 52

4.4

Circuit Examples................................................................................................ 53

4.4.1

Block Diagram of the SIM 1-2 and SPC 4-2 with Galvanic Isolation................. 53

4.4.2

Diagram of the SIM 1-2 and SPC 4-2 without Galvanic Isolation...................... 54

4.4.3

External Components (recommended values) .................................................. 55

4.4.4

Notes on the Transistor ..................................................................................... 56

4.5

Layout Proposal................................................................................................. 57

Putting into Operation.................................................................................................. 59

5.1

Putting into Operation for the First Time............................................................ 59

5.2

Test Points......................................................................................................... 60

Appendix ....................................................................................................................... 61

6.1

References ........................................................................................................ 61

6.2

Addresses.......................................................................................................... 62

Содержание ASIC SIM 1-2































































Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды