Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 20

Страница: 20 / 62

Functional Description of the SIM 1-2

SIM 1-2

C79000-G8976-C215-01

2.3.5 Receiver Input: RXIN

The received signal is coupled into the input filter over the external capacitor C

RXIN

(220 pF) and R

EX1

(10 k

Ω

2.3.6 Impedance Converter Output/Input: VE/VESRD

These two connectors must be directly connected with each other and then over
R

SENSEP

with the collector of the external transistor T1 and the external energy

storage CVE. The voltage at VE/VESRD is regulated to a constant 6.3 V.

2.3.7 Reference

Circuit

RIREF, RVCCVE, RVREG, RISOLL

Connect the contacts to the specified reference resistors.

Contact

Reference

resistor

Meaning

RIREF

All internal references are derived from the current
flowing through R

RIREF

RVCCVE

forms the reference for VCC and VE. The

RVCCVE pin must be backed up to GND by
capacitor C

RVCCVE

RVREG

forms the reference for VREG. The RVREG

pin must be backed up to GND by capacitor C

VREG

RISOLL

sets the middle current taken from the bus

system.

Notice:

The tolerance of reference resistors is included in the tolerance of the bus current.
You can achieve the minimum tolerance of 3 % with resistors that have a tolerance
of

≤

0.1 %. As an alternative, the bus current can be adjusted over R

RISOLL

Содержание ASIC SIM 1-2































































Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды