manualshive.com logo in svg

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Поделиться
Скачать
Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 22

Functional Description of the SIM 1-2 

 

SIM 1-2 

22 

C79000-G8976-C215-01 

2.3.11 Digital Interface: TXE, TXS, RXA, RXS 

Possible interconnection between the external interface circuit, for example 
SPC 4-2, and the SIM 1-2: 

●

  Direct connection of TXE, TXS, RXA, RXS with the digital input and output 

drivers of an external communication controller for the external application 
electronics. 

●

  Connection of TXE, TXS, RXA, RXS with the digital input and output drivers of 

an external communication controller galvanically isolated over optocouplers 
for the external application electronics. 

●

  Interfacing using the power-saving galvanic signal isolation over two 

optocouplers TXS and RXS. 

2.3.12  Test and Manufacturing Pins: TD, T0, T1, T2, TA 

For the SIM 1-2 to function perfectly, the test and manufacturing pins TD, T0, T1, 
T2, and TA must be connected to GND. 

2.3.13  Mode Setting GIM and VCM 

Galvanic Isolation Mode (GIM) 

This input is used to activate or deactivate the power-saving interface to the 
application.  

 

 GIM 

Meaning 

 High 

The power-saving pulse duration modulation is used both for the inputs 
(demodulator on TXS) and for the output (modulator on RXS). 

 

Low 

The power-saving pulse duration modulation is not active. 

Содержание ASIC SIM 1-2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды