manualshive.com logo in svg

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Поделиться
Скачать
Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 43

Technical Specifications 

SIM 1-2 
C79000-G8976-C215-01 

43

 

Manufacturing Notes 

 
 

Caution 1 

The 

ESD protection measures 

must always be adhered to for all electronic 

components. 

 

 
 

Caution 2 

The 

SIM 1-2 

is a 

component at risk of cracking

 that must be handled as such. 

 

•  Before processing the SIM 1-2, it must be subjected to a drying process if the 

chip has been stored for more than 168 hours without being dry packed 
(according to JEDEC J-STD-020C Moisture Sensitivity Level 3). 

•  The component must then by dried at 125 °C for 24 hours and processed within 

48 hours. This drying may only be performed once due to the solderability of the 
component (according to JEDEC J-STD-020C Moisture Sensitivity Level 3). 

•  The SIM 1-2 is approved for infrared reflow with the lead-free reflow profile 

according to JEDEC JSTD-020C. 

•  The lead-free infrared reflow process must not exceed a maximum temperature 

of 260 °C on the surface of the package and may be 260 °C for only three 
seconds. Over a period of maximum 150 seconds, the temperature of the 
package surface may exceed 217 °C (according JEDEC J-STD-020C). 

•  Lead finish: Sn 

 

Содержание ASIC SIM 1-2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды