manualshive.com logo in svg

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Поделиться
Скачать
Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 28

Functional Description of the SIM 1-2 

 

SIM 1-2 

28 

C79000-G8976-C215-01 

2.5 Internal 

Functions 

2.5.1 Impedance 

Converter 

The impedance converter/current modulator and current control function units 
together along with a few external components and the internal shunt regulator 
form the high-impedance decoupling of the auxiliary power from the bus cable. 

2.5.2 Shunt 

Regulator 

The shunt regulator derives a stabilized voltage VE from the constant current. The 
part of the total current not required by external loads is diverted to GND. The load 
current can be taken in any proportions from the power supplies VREG and the 
DC/DC converter (external transformer necessary).  

2.5.3 Signal 

Filter 

The combined input high pass,  band pass and low pass filter suppresses 
disturbances outside of the signal transmission range from 7 kHz to 40 kHz. The 
band pass and low pass filter is implemented as a switched capacity filter. The 
input high pass filter is made up of R

EX1

 and C

RXIN .

 

 

 

 

 

Содержание ASIC SIM 1-2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды