manualshive.com logo in svg

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Поделиться
Скачать
Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 5

 

SIM 1-2 
C79000-G8976-C215-01 

5

 

Preface 

Purpose of manual

 

 

This manual supports you during the development of a Fieldbus Medium 
Attachment Unit (MAU) for 31.25 Kbps in compliance with IEC 61158-2 with the 
SIM 1-2 (

S

iemens 

I

EC 

M

AU) and a small number of external components. 

Which Data Link Layer protocol is implemented is irrelevant. In conjunction with a 
suitable communication controller, for example SPC 2-4, devices with a fieldbus 
attachment (supplied with power locally or over the bus) can be implemented with 
little effort.  

This manual serves both as a function manual and as a data sheet for the 
developer of the electronics. 

Aims  

With the aid of this manual, you will be able to develop a fieldbus medium 
attachment unit (MAU) for 31.25 Kbps for your application with little effort using the 
SIM 1-2. 

We assume that you are familiar with the relevant standards and specifications. 

Certification  

The products and systems listed in this document are manufactured and marketed 
using a quality management system complying with DIN ISO 9001 and certified by 
DQS (certificate register no. 2613). The DQS certificate is recognized in all IQNet 
countries (Reg. No.: 2613). 

 

Содержание ASIC SIM 1-2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды