Siemens 7XV5550-0xA00 Series Скачать руководство пользователя страница 4

Страница: 4 / 52

Page 4 from 52

Active Mini-Starcoupler

14.01.2002

INSTALLATION AND COMMISSIONING .................................................................................... 26

5.1

Reference to Installation ........................................................................................................... 26

5.2

Connection................................................................................................................................ 26

5.2.1

Voltage for operation – Auxilliary voltage ......................................................................... 27

5.2.2

Alarm relay terminals X7 .................................................................................................. 27

5.2.3

Fibre Optic (FO) connections ........................................................................................... 27

5.2.4

RS232 connection ............................................................................................................ 28

5.2.5

Commissioning................................................................................................................. 28

5.3

Maintenance.............................................................................................................................. 28

MODES OF OPERATION............................................................................................................. 29

6.1

How to activate the operation mode ......................................................................................... 29

6.1.1

How to select the Active Transmission Mode .................................................................. 29

6.1.2

Passiv Transmission Mode .............................................................................................. 30

6.1.3

Termination of the Active Transmission MOde ................................................................ 30

6.1.4

Time out conditions .......................................................................................................... 30

6.1.5

Test aid for the data connection....................................................................................... 31

6.2

Activation of the Setting Mode .................................................................................................. 31

6.2.1

With DIGSI – cable 7XV5100-4 (Bridged between pin 7-8) ............................................ 31

6.2.2

With Zero-Modem Cable (Not bridged between pin 7-8) ................................................. 32

6.2.3

With standard parameters 9600 Baud, 8N1 (recommended) .......................................... 32

6.3

Setting of the interfaces ............................................................................................................ 33

6.3.1

With the terminal program "Hyper-Terminal" ................................................................... 33

6.3.2

The main setting dialogue / Change language................................................................. 34

6.3.3

Changing the parameters of a port (interface) ................................................................. 35

6.3.4

Saving parameters ........................................................................................................... 38

6.3.5

Termination of the Setting mode ...................................................................................... 38

CHANGE THE FIRMWARE IN THE DEVICE............................................................................... 39

7.1

Warnings................................................................................................................................... 39

7.2

How to change the firmware ..................................................................................................... 39

APPLICATIONS TOGETHER WITH SIPROTEC RELAYS ......................................................... 40

8.1

SIEMENS-Relays of version 1/2 together with DIGSI V3 ......................................................... 40

8.1.1

Functional limitations with V1 / V2 protection devices...................................................... 44

8.2

SIEMENS-Relays of version 1/2 and 3 together with DIGSI V3 .............................................. 45

8.2.1

Operation with DIGSI 4.3x................................................................................................ 46

8.3

SIEMENS-Relays of version 1/2/3 and SIPROTEC 4 relays together with

DIGSI V3 or DIGSI 4................................................................................................................. 48

8.3.1

Operation with DIGSI 4.3x................................................................................................ 49

Содержание 7XV5550-0xA00 Series





















































Результаты поиска

Содержание 7XV5550-0xA00 Series

Отзывы:

Похожие инструкции для 7XV5550-0xA00 Series

Бренды по названию

Популярные бренды

Siemens 7XV5550-0xA00 Series, Руководство пользователя

Результаты поиска

Содержание 7XV5550-0xA00 Series

Отзывы:

Похожие инструкции для 7XV5550-0xA00 Series

Бренды по названию

Популярные бренды