Siemens 7XV5550-0xA00 Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 52

background image

14.01.2002

Active Mini-Starcoupler

Page 45 from 52

8.2

SIEMENS-Relays of version 1/2 and 3 together
with DIGSI V3

One Active Mini-Starcoupler allows the central and remote interrogation
of max. 4 non addressable relays of version 1 or 2 and with further
starcouplers, which are conncted to one Slave-interface, up to 250
addressable relays from version 3 can be in the topology. Each relay of
version 1/2 needs an optical interface. The number of non addressable
relays in a topoloy can be increased, if several Active Mini-Starcouplers
are cascaded with the RS485 bus. The interface parameters of the
Slave-interfaces must be set according the settings for the front –
interface of the relays. The port selection procedure and the operation
with the relays of version 1/2 or 3 is part of DIGSI 3 and comfortable
supported by this program. How do set the parameters for DIGSI V3 is
written in the DIGSI – manual, which is on the DIGSI – installation CD-
ROM as a PDF-file.

In the following application non addressable relays ( V1/2) and
addressable relays (V3) can be centrally interrogated with the max.
baudrate, allowed for the relays serial interface.

Settings for the Master-device (close to the PC / modem)
for the application shown in fig. 5

Interface Chan. Baud

Data

TimeOut

Light Ping Answ.

1

0

19200 8E1

06:00:00

NO

NO

YES

2

2

1200 8N2

05:00:00

NO

-

-

3

3

9600 8N2

05:00:00

NO

-

-

4

4

9600 8N2

05:00:00

NO

-

-

5

5

19200 8E1

05:00:00

NO

-

-

6 (RS485)

0

19200 8E1

06:00:00

NO

YES

7 (RS232)

0

19200 8E1

06:00:00

NO

YES

8 Back to Main Menu

The RS232-interface at connection point 7 (RS232/M0 in fig. 5) is set as
Master-interface (port number 0) and realizes the local, central access to
the relays with DIGSI 3. Also the settings of the device are made via this
interface.

The optical interface at connection point 1 (FO/M0 in fig. 5) is connected
with the modem and set as Master-interface. Through this interface runs
the remote interrogation. If the automatic baud rate adaption in the

«
...
43
44
45
46
47
...
»

Содержание 7XV5550-0xA00 Series





















































Отзывы:

Нет отзывов

Похожие инструкции для 7XV5550-0xA00 Series

Бренд: SIMON RWA Страницы: 3

SynOptics 3000 Series

Бренд: Cabletron Systems Страницы: 101

Бренд: I/O Interconnect Страницы: 27

Бренд: Cabletron Systems Страницы: 83

Smart Switch 2:1

Бренд: XTBA Страницы: 3

Бренд: Cypress Страницы: 4

Бренд: MLis Страницы: 85

Бренд: Xantech Страницы: 32

Extricom AT-EXLS-3000

Бренд: Allied Telesis Страницы: 120

Бренд: DigitalZone Страницы: 20

XGS-6350-12X8TR

Бренд: Planet Страницы: 16

Бренд: Allied Telesis Страницы: 44

Бренд: Scion-Tech Страницы: 9

Бренд: Alaxala Страницы: 249

Бренд: Efapel Страницы: 44

Бренд: Kramer Страницы: 2

Бренд: ICP DAS USA Страницы: 70

Expert Power Control NET 24x

Бренд: Gude Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды