manualshive.com logo in svg

Siemens 7MB2041, Руководство по эксплуатации, Страница: 7 / 152

Поделиться
Скачать
Siemens 7MB2041 Скачать руководство пользователя страница 7

 

Table of contents 

  

OXYMAT 64 
Operating Instructions, 06/2008, A5E00880383-03 

5

 

5.4.5 

Parameters...................................................................................................................................70 

5.4.5.1  Parameters submenu...................................................................................................................70 

5.4.5.2  Electric time constants (function 50)............................................................................................71 

5.4.5.3  Limits (function 51).......................................................................................................................72 

5.4.5.4  On/off functions (function 52).......................................................................................................73 

5.4.5.5  Status messages (function 53) ....................................................................................................74 

5.4.5.6  Graphical representation of measured values (function 54)........................................................75 

5.4.5.7  Measured value display (function 55) ..........................................................................................77 

5.4.5.8  LCD contrast (function 56)...........................................................................................................77 

5.4.5.9  Date/time (function 58).................................................................................................................78 

5.4.5.10  Measuring point switching (function 59) ......................................................................................79 

5.4.5.11  Logbook settings (function 60).....................................................................................................80 

5.4.6 

Configuring...................................................................................................................................81 

5.4.6.1  Configuration submenu................................................................................................................81 

5.4.6.2  Analog output (function 70)..........................................................................................................81 

5.4.6.3  Relay outputs (function 71)..........................................................................................................82 

5.4.6.4  Binary inputs (function 72) ...........................................................................................................84 

5.4.6.5  ELAN configuration (function 73).................................................................................................87 

5.4.6.6  Reset (function 74).......................................................................................................................88 

5.4.6.7  Save, load data (function 75).......................................................................................................88 

5.4.6.8  Suppression of short-term noise signals (function 76) ................................................................90 

5.4.6.9  Analog output memory (function 77)............................................................................................91 

5.4.6.10  Calibration tolerances (function 78) .............................................................................................91 

5.4.6.11  Change codes (function 79).........................................................................................................93 

5.4.6.12  Device test (function 80) ..............................................................................................................93 

5.4.6.13  Language selection (function 81).................................................................................................95 

5.4.6.14  Correction of cross-interference (function 83) .............................................................................95 

5.4.6.15  Switch valves (function 85) ..........................................................................................................98 

5.4.6.16  Error on/off (function 87)..............................................................................................................99 

5.4.6.17  PROFIBUS configuration (function 90)........................................................................................99 

5.4.6.18  Changing the dimension (function 91) .......................................................................................100 

5.4.6.19  Factory settings (function 99).....................................................................................................102 

6 

Repair, maintenance and servicing........................................................................................................ 103 
6.1 

Important maintenance information ...........................................................................................103 

6.2 

Sensor module...........................................................................................................................104 

6.2.1 

Design........................................................................................................................................104 

6.2.2 

Installation and removal of the sensor module ..........................................................................104 

6.2.3 

Installation/retrofitting of pressure regulator ..............................................................................106 

6.3 

Replacement of motherboard and optional board .....................................................................107 

6.4 

Replacement of fuses ................................................................................................................107 

6.5 

Cleaning the device ...................................................................................................................108 

6.6 

Removing faults .........................................................................................................................109 

6.6.1 

Alarms and messages ...............................................................................................................109 

6.6.2 

Maintenance requests................................................................................................................110 

6.6.3 

Fault messages..........................................................................................................................111 

6.6.4 

Other faults.................................................................................................................................112 

7 

Technical data

  

...................................................................................................................................... 113 

8 

Dimension drawings and charts............................................................................................................. 117 
8.1 

Dimension drawings...................................................................................................................117 

8.2 

Gas flow chart ............................................................................................................................119 

Содержание 7MB2041

























































































































































Отзывы:

Нет отзывов