Siemens 7MB2041 Скачать руководство пользователя страница 144

Страница: 144 / 152

Glossary

OXYMAT 64

142

Operating Instructions, 06/2008, A5E00880383-03

Limit relay

Relay to which a certain limit is assigned and which is switched when there is a limit alarm.

Main menu

Menu of the highest hierarchical level. It contains the submenus.

Measured signal

Representation of measured variables in the signal path by an allocated physical quantity of

the same or different type. Depending on the position of the measured signal at the input or

output of the considered element, one distinguishes between an input signal and an output

signal.

Measured value

Output value for a determined variable.

Measured value display

Totality of the displayed information in "Coded display mode" and "Decoded display mode".

The following are displayed, for example: measured value, status line with status messages,

footer, measuring ranges, components, etc.

Measuring point

Location where a measured value is recorded.

Measuring point relay

Relay to which a measuring point is allocated.

Measuring range

The measuring range is the range of values for a measured variable. The limits of the

measuring range are the start-of-scale and full-scale values. This means that the start-of-

scale and full-scale values are known for the measuring range.

Measuring range switching

Automatic switching over of measuring ranges. Also referred to as "autorange" in the

software.

Membrane keyboard

Keyboard whose keys are protected jet-proof against atmospheric influences by a

membrane (IP 65 according to EN 60529).

Содержание 7MB2041

























































































































































Результаты поиска

Содержание 7MB2041

Отзывы:

Siemens 7MB2041, Руководство по эксплуатации, Страница: 144 / 152

Результаты поиска

Содержание 7MB2041

Отзывы: