Siemens 7MB2041 Скачать руководство пользователя страница 108

Страница: 108 / 152

Repair, maintenance and servicing

6.2 Sensor module

OXYMAT 64

106

Operating Instructions, 06/2008, A5E00880383-03

6.2.3

Installation/retrofitting of pressure regulator

If a pressure regulator has to be replaced or retrofitted, proceed as follows:
1.

Remove sensor module

Mount the pressure regulator onto the sloping upright plate of the metal bracket using two

M5 screws.

Reinstall the sensor module.

Fit the supplied capillary tube (without restrictor) between the sample gas inlet coupling

and the gas inlet of the pressure regulator.

Fit the supplied capillary tube with restrictor between the input of the T-piece present on

the O

sensor and the output of the pressure controller.

Carry out a leak test as described in Section 'Commissioning and operation'.

Apply a sample gas pressure (> 0.2 MPa) and turn the screw of the pressure controller

until the cone floats in the flowmeter tube. Then adjust the setpoint flow (125 ml/min)

using the bypass restrictor.

Note
Make sure that none of the small parts (gasket cone, sleeve, pressure piece, union nut)

are lost when fitting the capillary tube. In addition, do not overtighten the union nut,

otherwise the gasket (PTFE) will be permanently deformed and lose its sealing function.

Содержание 7MB2041

























































































































































Результаты поиска

Содержание 7MB2041

Отзывы:

Siemens 7MB2041, Руководство по эксплуатации, Страница: 108 / 152

Результаты поиска

Содержание 7MB2041

Отзывы: