Siemens 7MB2041 Скачать руководство пользователя страница 145

Страница: 145 / 152

Glossary

OXYMAT 64
Operating Instructions, 06/2008, A5E00880383-03

143

Motherboard

Board which contains the basic data and firmware for the device. Here, data are processed

and stored, and interfaces and device I/Os are controlled and managed.

Noise

Totality of all phenomena which could disturb the transmission and/or recording of

information.

Operating mode

Various modes into which the device can be put by intervening from the outside. Three

modes are distinguished:
●  Coded display mode
●  Decoded display mode
●  Operator control mode

Operating state

Common term for all states in which the device can be found during operation (e.g. measure,

fault, calibration, ...).

Operation level

Certain operating area (menus and functions) which is either freely accessible or protected

by a code.

Operator control mode

Operating mode in which the device is partially or entirely decoded and the functional check

is activated. The device is parameterized in this mode.

RC element

An RC element in electronics is a circuit comprising an ohmic resistor (R) and a capacitor

(C).

Sample gas

A gas which has been extracted from a process and is to be analyzed.

Signaling contact

Usually a floating contact contained in electronic components (e.g. relay) which signals the

occurrence of an event to a control unit.

Содержание 7MB2041

























































































































































Результаты поиска

Содержание 7MB2041

Отзывы:

Siemens 7MB2041, Руководство по эксплуатации, Страница: 145 / 152

Результаты поиска

Содержание 7MB2041

Отзывы: